Calypso BTS: my phone my phone doesn't see my base station

classic Classic list List threaded Threaded
3 messages Options
Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

Calypso BTS: my phone my phone doesn't see my base station

phreaker1983
This post has NOT been accepted by the mailing list yet.
hi guys, my phone doesn't see my base station.. To start I used :
1. First terminal:
   ~/osmocombb/trx/src# sudo host/osmocon/osmocon -m c123xor -p /dev/ttyUSB0 -c target/firmware/board/compal_e88/trx.highram.bin -r 99

2. Second terminal:
 ~/osmocombb/trx/src/host/layer23/src/transceiver# sudo ./transceiver -a 40 -r 99

Then I showed
<0012> l1ctl.c:383 Reset received: Starting sync.
<0012> l1ctl.c:338 Sync acquired, setting BTS mode ...
<0011> trx.c:194 TRX CLK Indication 1890062
<0011> trx.c:194 TRX CLK Indication 1890113
<0011> trx.c:194 TRX CLK Indication 1890164
<0011> trx.c:194 TRX CLK Indicatn 1890215
                                                                   ........
3. third terminal:
osmo-nitb -c ~/.osmocom/open-bsc.cfg -l ~/.osmocom/hlr.sqlite3 -P -C —debug=DRLL:DCC:DMM:DRR:DRSL:DNM

DB: Database initialized.
DB: Database prepared.

My open-bsc.cfg contains:
! OpenBSC configuration saved from vty
! !
password foo
!
line vty
no login
!
e1_input
e1_line 0 driver ipa
network
network country code 1
mobile network code 1
short name OpenBSC
long name OpenBSC
auth policy closed
location updating reject cause 13
encryption a5 0
neci 1
rrlp mode none
mm info 1
handover 0
handover window rxlev averaging 10
handover window rxqual averaging 1
handover window rxlev neighbor averaging 10
handover power budget interval 6
handover power budget hysteresis 3
handover maximum distance 9999
timer t3101 10
timer t3103 0
timer t3105 0
timer t3107 0
timer t3109 4
timer t3111 0
timer t3113 60
timer t3115 0
timer t3117 0
timer t3119 0
timer t3141 0
bts 0
type sysmobts
band DCS1800
cell_identity 0
location_area_code 1
training_sequence_code 7
base_station_id_code 63
ms max power 15
cell reselection hysteresis 4
rxlev access min 0
channel allocator ascending
rach tx integer 9
rach max transmission 7
ip.access unit_id 1801 0
oml ip.access stream_id 255 line 0
gprs mode none
trx 0
rf_locked 0
arfcn 514
nominal power 23
max_power_red 20
rsl e1 tei 0
timeslot 0
phys_chan_config CCCH+SDCCH4
timeslot 1
phys_chan_config SDCCH8
timeslot 2
phys_chan_config TCH/F
timeslot 3
phys_chan_config TCH/F
timeslot 4
phys_chan_config TCH/F
timeslot 5
phys_chan_config TCH/F
timeslot 6
phys_chan_config TCH/F
timeslot 7
phys_chan_config TCH/F

arfcn I chose the 514.....
4. fourth terminal:
 cd /osmocombb/osmo-bts/src/osmo-bts-trx
osmo-bts-trx -c ~/.osmocom/osmo-bts.cfg

showed me:
((*))
|
/ \ OsmoBTS
<0017> control_if.c:693 CTRL at 127.0.0.1 4238
<0010> telnet_interface.c:95 telnet at 127.0.0.1 4241
<0012> input/ipaccess.c:881 enabling ipaccess BTS mode
<0006> phy_link.c:58 PHY link state change shutdown -> connectiong
<0006> scheduler.c:174 Init scheduler for trx=0
<000b> trx_if.c:584 Open transceiver for phy0.0
<0006> phy_link.c:58 PHY link state change connectiong -> connected
<0006> phy_link.c:68 trx_set_avail(1)
<0006> scheduler_trx.c:1514 GSM clock skew: old fn=0, new fn=1908169
<0006> scheduler_trx.c:1519 GSM clock jitter: -691
<0006> scheduler_trx.c:1519 GSM clock jitter: 128
<0006> scheduler_trx.c:1519 GSM clock jitter: 674
<0006> scheduler_trx.c:1519 GSM clock jitter: 204
<0006> scheduler_trx.c:1519 GSM clock jitter: 467
<0006> scheduler_trx.c:1519 GSM clock jitter: -1620
<0006> scheduler_trx.c:1519 GSM clock jitter: 1362
<0006> scheduler_trx.c:1519 GSM clock jitter: -668
<0006> scheduler_trx.c:1519 GSM clock jitter: -846
<0006> scheduler_trx.c:1519 GSM clock jitter: 519
<0006> scheduler_trx.c:1519 GSM clock jitter: 457
<0006> scheduler_trx.c:1519 GSM clock jitter: 384
<0006> scheduler_trx.c:1519 GSM clock jitter: 218
                                                                           .....
 My osmo-bts.cfg contains:
!OsmoBTS (0.0.1.100-0455) configuration saved from vty
!!
!
phy 0
instance 0
bts 0
band DCS1800
ipa unit-id 1801 0
oml remote-ip 192.168.100.11
trx 0
phy 0 instance 0

Where I erred? Thank you.
Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

Re: Calypso BTS: my phone my phone doesn't see my base station

phreaker1983
This post has NOT been accepted by the mailing list yet.
Sorry I do not fully understand where to change the signal strength... in my file open-bsc.cfg in section trx , nominal power is equal to 23. Where should I make changes ?
Reply | Threaded
Open this post in threaded view
|  
Report Content as Inappropriate

Re: Calypso BTS: my phone my phone doesn't see my base station

phreaker1983
This post has NOT been accepted by the mailing list yet.
Could you check the contents of my osmo-bts.cfg and open-bsc.cfg and I run OpenBTS?
Loading...